How To Take Apart A Kimber 1911

Kimber 1911 Field Strip- Disassembly & Reassembly Instructions

This article volition show you step-past-footstep how to detach (Field Strip) and reassemble a Kimber Aegis Elite Custom 1911 Semi-Automatic Pistol in .45 ACP.  You will need to know how to perform a 1911 field strip for cleaning purposes. For just the Disassembly, come across How to Detach a Kimber 1911.

Here is some information on setting up a Homemade Gun Cleaning Station.

Which 1911 models does this Procedure Piece of work For?

This 1911 disassembly and reassembly procedure will work for near, if not all makes and models of 1911 pistols with a five″ barrel. Some will be referred to every bit "Government" models. The M1911 pistol is the original designation for the 5″ Government model.

Different Manufacturers may utilise other names to signify a 5″ total size 1911. For example, Kimber refers to some of their 5″ models every bit "Custom", such as Main Carry Custom. The Principal Carry Pro will have their 4″ barrel, and the Master Bear Ultra will accept a 3″ Barrel.

This 1911 disassembly reassembly field strip procedure will not work for a Kimber model with a "bull butt". Almost of the 4″ 1911 Models use a different design to lock the butt to the slide. If you have the 4″ model, come across my article Cleaning a Kimber 1911 Pro Bear. or Kimber Pro Acquit II Disassembly.

1911 Barrel Bushing on Left, Bull Barrel on Right

Field stripping is basically removing the slide from the frame, and and then removing the recoil spring, guide rod and barrel. Once this is achieved, these components can then be cleaned and lubed every bit outlined in my commodity: Cleaning a Kimber 1911.

The cleaning procedure and products used volition certainly work on any 1911, and almost other guns equally well. Just be aware that if you are going to clean a Glock, Springfield XD serial or Smith & Wesson Thousand & P firearm or other gun with "plastic" parts, be sure to apply a cleaner designed for that apply, such every bit Birchwood Casey Gun Scrubber Synthetic Safe Cleaner. Some of the more mutual cleaners are harsh on plastics and polymers.

If this is the showtime time you are doing this, do not fear! Information technology is not hard if y'all follow the steps. The adjacent fourth dimension you do it you will be a pro and volition not likely need these instructions. It looks like a lot of steps only I wanted to interruption it down as far as I could to brand it as clear and like shooting fish in a barrel equally possible.

1911 Disassembly Tools

You lot will need a 1911  barrel bushing wrench for this procedure:

1911 Barrel Bushing Removal Wrench

‏Real Avid Smart Bench Block built-in Barrel wrench

Or a cracking little product I recently purchased called a Real Avid Smart Bench Block which has a congenital-in butt bushing wrench. you tin cheque it out here.

Footstep by step instructions are beneath, but you can also watch my videos. The first is for the 1911 Field Strip and the 2nd is the reassembly.

1911 Disassembly Video

Here is the reassembly video:

Step by Pace Instructions with Pictures: Disassembly-Field Strip a 1911

Here is the 1911 Nosotros are Going to Field Strip

Here are the steps:

Remove the magazine

Empty the chamber of any rounds

Echo the last ii steps. BE Sure THE GUN IS UNLOADED.

Set the gun on a tabular array or bench with the barrel facing upwardly. Wear eye protection in case the recoil spring launches the plug into your face.

Line upward the butt bushing wrench with the bushing and apply downward pressure level on the plug until you can turn the wrench.

Turn the wrench clockwise to the ix o'clock position.

Carefully and slowly reduce pressure and allow plug to rise every bit tension is released from the recoil spring. Be careful or the leap will launch the plug across the room. I know this for a fact!

.

In one case the recoil spring is loose, the slide will motion easily.

Line upwards the notch in the slide with the Slide lock lever as shown.

Printing on the slide Lock lever pin on the opposite side of the gun to offset pushing information technology up enough to grab it.

Remove the slide lock Lever and set information technology aside.

Remove the slide by pulling it off the front of the frame.

Remove the recoil spring from the slide assembly by pulling it out the front and remove the guide rod every bit well by pulling it upward out the back.

Employ the barrel bushing wrench and plough the bushing counter-clockwise nearly as far as information technology volition go. There is a "cardinal way" that needs to line up with the notch in the slide.

Remove the barrel bushing past pulling it out the front. Use the barrel to help push it out if necessary.

Remove butt from the front of the slide. You likely will need to flip the barrel lug forward so information technology will fit.

You take now field stripped your 1911.

Now you can clean and lubricate each component.

Reassembly Steps with Pictures: 1911 v″ Government Pistol

Identify the slide upside down on your bench and slide the barrel  into the slide.

Line up the barrel bushing as shown and press it into identify firmly against the front end of the slide.

Using the butt bushing wrench, turn the bushing clockwise to the 9 o'clock position.

Lay the slide on the bench upside down and identify the guide rod on top of the butt as shown.

Slide the tighter, smaller finish of the recoil spring onto the guide rod and seat it firmly.

Slide the tighter, smaller stop of the recoil leap onto the guide rod and seat it firmly.

While belongings the barrel and guide rod in place, turn the slide sideways as shown and be sure the butt lug is perpendicular to the butt.

Slide the associates onto the rail of the frame until the barrel lug is lined upwardly with the hole in the frame.

Insert the slide stop pivot through the hole in the frame and line up the notch in the slide with the square hole in the frame as shown.

Line upwards the slide cease lever with the pigsty.

** Be careful here. If you do not line things up as shown, yous may scratch your gun when pressing the lever into place.

Press the lever into place by applying fifty-fifty pressure level to both ends of the lever.

Once in place, motion the slide all the way forward and lock it there with the safety lever.

Place the gun on the demote facing up.

Identify the plug on the end of the recoil jump.

Line up the wrench with the barrel bushing and press downward on the plug until the wrench is affluent with the cage.

Maintaining downward pressure, plow the wrench counter clockwise to the 6 o'clock position.

Make sure the barrel bushing is properly lined upwards with the plug

Congratulations! Yous're washed reassembling your 1911!

Final Steps

Now piece of work the slide dorsum and forth with your support hand to make sure it feels correct and to help the lubricant move into all the moving parts. Then wipe any excess lube off of the gun with a rag or paper towel.

Now be certain to perform a 1911 part and prophylactic check.

If you accept some dummy rounds or snap caps, you can use these to exam the proper ejection of your firearm without using live ammunition.

You have successfully field stripped and reassembled your 1911. If your gun does not accept a barrel bushing, please encounter Cleaning a Kimber 1911 Pro Carry for instructions on the disassembly on a Kimber with a bull barrel.

Source: https://kydexowbholsters.com/field-stripping-and-reassembling-a-kimber-1911

Share this post